Cadillac Radiator Grille
Installation Videos

Welcome to Part 7 of Project 928! With the intake manifold finally out of the way, we take a closer look at the components underneath—and discover major discrepancies between the Bring a Trailer auction receipts and reality. We investigate parts that were supposedly replaced years ago but are nowhere to be found, test the suspiciously original-looking Throttle Position Sensor (TPS), and prep the intake for reinstallation. But finding these sketchy records leaves us with a massive decision: do we trust the 2020 timing belt receipt included with the car, or do we tear the front of the engine down and replace it just for peace of mind? What would you do in our situation? Let us know in the comments below! If you enjoyed the video, please hit that LIKE button and SUBSCRIBE to the channel so you don't miss Part 8!

Welcome back to Part 6 of Project 928! We are still hunting down the cause of our persistent rough idle and hesitation. After swapping the MAP and TEMP2 sensors with only mild improvement, a carb cleaner test revealed we have unmetered air slipping in right under the intake manifold. In this episode, we tear into the top end of the V8 to pull the intake. We walk you through the process of clearing the airbox and MAF, safely disconnecting the fuel injector rails, marking our vacuum lines, and wrestling with the notoriously tight TPS and idle control valve connections. Once the intake was finally out of the way, we found exactly what we were looking for: a massive split in the idle control valve tube. Based on the dirt, this thing has been wide open and sucking unmetered air for a long time! We also took the opportunity to clean up the notoriously difficult engine grounds at the back of the block and evaluate our original single-pintle injectors (spoiler: we're calling Roger at 928sRus for a 4-hole upgrade). THE REVEAL: Finding the massive vacuum leak Testing the flappy valve and TPS sensor Do you think this split idle control valve tube is the root cause of all our running issues? Drop a comment below and let us know what you think! If you enjoyed the video, please hit that LIKE button, SUBSCRIBE to the channel, and turn on notifications so you don't miss Part 7 when we start putting it all back together with some fresh upgrades.

In Part 5, we are investigating the lumpy idle and 1,400 RPM fail-safe mode on our Bring a Trailer 1989 Porsche 928 S4. The seller claimed this car was ready to drive anywhere, but we found a dead Temp 2 sensor and an open loop reading on the mass airflow sensor (MAF). Watch as Eric tests the resistance on the sensors, inspects the wiring harness, and shares a few quick updates on the dyed black console, fixed rear headliner, and new rear hatch parts from Roger at 928s R US. Video Highlights: Testing the Temp 2 sensor with a multimeter Inspecting the MAF wiring harness and connector Reading ohms between pins 1 & 4 and 2 & 4 on the MAF sensor Updates on the console color match, headliner repair, and rear hatch latch Let us know your thoughts and advice in the comments below! 🛒 SHOP AT radiatorgrillestore.com #Porsche928 #PorscheRestoration #BringATrailer #RadiatorGrilleStore #ProjectCar

Here’s a quick update on the interior repairs for our Bring-A-Trailer 1989 Porsche 928 S4! In this video, we review the finished results from Part 3. The once-maroon center console is now fully black to match the cabin, and our steamed rear headliner panel is significantly flatter and ready to clip back into place—a huge improvement over the sagging, warped board we started with! Subscribe to follow along with our ongoing Project 928 restoration! 🛒 SHOP AT radiatorgrillestore.com #Porsche928 #928S4 #BringATrailer #PorscheRestoration #ProjectCar #RadiatorGrilleStore

Welcome back to Part 3 of fixing up our Bring-A-Trailer 1989 Porsche 928 S4! In this episode, we take a break from electrical issues to tackle some much-needed interior restoration. First, we fix a mismatched maroon center console using black leather balm—and the results turned out way better than expected while keeping that classic original patina. Next, we address the warped rear sun visor headliner panel mentioned in the auction using hot towels, a clothing steamer, and heavy weights to straighten out the board. What we cover in this video: Cleaning and prepping leather using alcohol Applying leather balm with a brush and swirling technique Steaming and reshaping warped interior fiberboard Covering up old accessory mounting holes in the dash leather 📺 Subscribe to follow along and see how these interior repairs turned out in the next video! 🛒 SHOP AT radiatorgrillestore.com #Porsche928 #928S4 #BringATrailer #PorscheRestoration #ProjectCar #RadiatorGrilleStore

Upgrade the rear end of your Porsche 992.1 in seconds! In this video, Eric demonstrates our custom rear bumper diffuser fins designed specifically for the Porsche 992.1 equipped with the GTS bumper, Sport Design package, or Aero Kit. These snap-in fins add an aggressive, impactful look to your rear diffuser with zero tools required. They feature a secure, structural clip fitment and are 100% reversible whenever you want to take them off. What you'll learn in this video: How to quickly snap on the right, center, and left diffuser fins How to easily remove them using the release tabs Quick fitment troubleshooting tips using the lower Torx adjustment screw 🛒 SHOP AT radiatorgrillestore.com #Porsche992 #Porsche911 #RadiatorGrilleStore #PorscheMods #PorscheGTS

This is not what we expected for our first day with this car. We just bought this 1989 Porsche 928 S4 off Bring a Trailer. We thought it was ready to drive, but right now we are dealing with a dead battery, broken lights, and a lot of electrical problems. Let this be a warning about buying a car without seeing it in person first. If there are any 928 experts out there, please let us know in the comments where you think we should start fixing it! → Follow our progress and get more updates on our social media channels: @radiatorgrillestore

Want to make a massive visual impact the next time you pop the hood at a car show? Eric shows you how to completely transform the engine bay of our C8 Z06 with the premium Hulse Design air intake covers! 🛠️🎨 We went with a custom Amplify Orange paint match to perfectly compliment the car, but these are available in an array of finishes. Including standard gloss or matte carbon fiber, red carbon fiber, and multiple paint-matching schemes. Check out that final look! This is a must-have upgrade to ensure your Z06 stands out from the crowd. 🏁 👉 Upgrade your engine bay today at RadiatorGrilleStore.com! 📲 Make sure to follow our social media accounts (Facebook and Instagram) for more shop builds, product drops, and updates:@radiatorgrillestore #C8Corvette #CorvetteZ06 #C8Z06 #HulsaDesign #EngineCover #AmplifyOrange #RadiatorGrilleStore #RGS #CarMods #CorvetteNation #DIYInstall #CarShowReady